Linear Gate Motor & Opener Nationwide

Linear Gate Motor & Opener in Little Elm: What to Know First

Linear gate motors and openers in Little Elm can usually be repaired in one visit, and most jobs run between $180 and $640 depending on what failed. We’re an independent Linear service provider - not factory-authorized, which means we answer to you, not to a manufacturer’s script. If the motor turns but the gate won’t move, if the opener hums and stops, or if the keypad stopped talking to the board, call (432) 547-6481 and we’ll give you a straight answer before we ever send a truck.

Call (432) 547-6481

This page is for homeowners in Little Elm who own a Linear gate opener and want to know what’s wrong, what it takes to fix it, and what it should cost. We’ve worked on Linear equipment across Denton County for over four decades at Ironworks Gate Co., and Victor Salinas has seen just about every way these units age in Texas heat.

How Linear Products Fail - and How We Fix Them

Linear builds solid entry-level and mid-range operators, but they have a few repeat offenders we see across Little Elm neighborhoods like Paloma Creek, Frisco Hills, and Lakewood Hills. Here’s what actually goes wrong:

• Linear LSO/OSCO series slide motors and the “hum, no movement” problem. These are swing and slide operators that rely on a start capacitor to kick the motor over. In Little Elm’s summer heat, that capacitor degrades fast - we replace more Linear capacitors in July and August than any other single part. The symptom is specific: the opener hums for two or three seconds, then trips its thermal overload. A capacitor swap gets most of them running again the same day.
• Linear APeX and MegaCode receivers losing their memory. The on-board receiver on older Linear control boards uses a small rechargeable memory cell. Once that cell dies, every remote and keypad in the system forgets its code at random intervals. Owners often mistake this for a bad remote and start replacing batteries or buying new transmitters. The real fix is reflashing or replacing the receiver module, which is a fraction of what a full board replacement costs - and it’s the kind of distinction you only catch if you’ve opened enough of these boxes.
• Limit switches on the Linear SlideGate Operator drifting out of adjustment. The mechanical limit cams on Linear slide operators wear visibly after five to seven years of daily cycles. The gate starts stopping six inches short, then two feet short, then it slams the end stop. We resynchronize the cams and the travel adjustment on every Linear repair, because a gate that over-travels will chew through rollers and stress the chain.
• Water intrusion in the Linear enclosure after heavy North Texas storms. The factory enclosures are weather-resistant, not weatherproof - and a wind-driven Little Elm rain can push moisture past tired gaskets. Once moisture sits on a Linear control board, you get phantom activations, dead keypads, or the gate refusing to close during a storm. We dry out the enclosure, replace the gaskets, and if the board is scorched, we source a correct-spec replacement rather than a generic swap.
• Battery backup failure on Linear models with the optional DC backup module. Little Elm sees its share of thunderstorm outages, and a Linear backup battery that hasn’t been load-tested in three years will test fine one day and be dead the next. We test backup batteries under load, not just with a voltmeter, because a battery that holds 12.6 volts sitting still can collapse the moment the gate needs to move.

Our Linear Gate Motor & Opener Process

We don’t do mystery billing. The price is set before a single bolt turns, in writing, and it doesn’t change unless you approve a change in scope. Here’s how a typical Linear repair goes with us:

1. 1
   You call (432) 547-6481. A live person answers - 24 hours a day, 7 days a week. No voicemail tree, no answering service. We ask what the gate is doing and what model opener you have, if you know it.
2. 2
   We show up when we say. A background-checked, uniformed technician arrives at your Little Elm home and starts by watching the gate run - or try to run. Most Linear problems reveal themselves in the first two minutes of observation.
3. 3
   We diagnose and show you. We’ll walk you through what failed, why it failed, and what it takes to fix it. If something doesn’t need replacing, we’ll tell you that too. Victor learned early that a customer who trusts your honesty calls you back - and tells their neighbors.
4. 4
   Parts decision, made together. Where an OEM Linear part is the right call, we order it. Where a quality aftermarket component is a better value and won’t void a meaningful warranty, we say so. Either way, the price is agreed before we start the work.
5. 5
   The repair, the test, the cleanup. We fix it, then we cycle the gate ten times in each direction, check the force settings, and make sure the safety edges and photo eyes work. We leave your driveway cleaner than we found it.
6. 6
   90-Day Done Right Promise. Every Linear repair is covered by our written guarantee. If it is not right, we come back and make it right - no arguing, no exceptions.

What Linear Gate Motor & Opener Costs in Little Elm

Here are the real numbers for the Linear jobs we do most often in Little Elm:

• Capacitor replacement: $180-$260
• Receiver or radio module replacement: $220-$380
• Limit switch adjustment and travel reset: $160-$240
• Control board replacement: $320-$640
• Full Linear opener swap (like-for-like): $850-$1,400 installed, depending on motor size and gate type

What moves the price: whether the gate is a slide or a swing, how old the existing unit is, and whether the concrete pad and wiring are in reusable shape. What doesn’t move the price: surprise line items. We quote upfront, we explain the quote, and we stand behind it. Call (432) 547-6481 for a free estimate on any Linear gate motor or opener work. And remember our standing offer: $50 off any repair over $250, and a permanent 5% discount for seniors and veterans.

Why Little Elm Homeowners Call Ironworks Gate Co. for Linear Work

We’ve been doing this for over 42 years, since before Little Elm stretched east past the tollway. We’re not a handyman service that happens to know one brand - we carry factory training and field experience across nine gate-automation brands: Linear, LiftMaster, Mighty Mule, Ghost Controls, DoorKing, FAAC, BFT, Viking, and Elite. That matters when a Linear board dies and a neighbor suggests swapping in something else. It matters when a homeowner can’t remember which motor they have. And it matters most when the fix isn’t obvious, because we’ve seen the same failure on five other brands and know exactly what to test next. We fix it right the first time, or we come back and fix it right.

FAQs