Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Highland Village
Gate parts and welding in Highland Village comes down to two things: the metalwork that holds your gate together, and the post that holds it in the ground. We handle both. A sagging ornamental gate, a rusted hinge pin, a post that has drifted out of plumb after three hard Texas drought years - these are the calls we take every week from homeowners along Yacht Club Road, Highland Shores, and the newer cul-de-sacs east of Briarhill Boulevard. If your gate is dragging, binding, or not latching, call us at (432) 547-6481 and we will get a technician out to Highland Village to look at it. The quote is free, and the price is set before any work begins.
We are Gate Parts & Welding specialists, not a handyman with a truck and a welder. That distinction matters when you have a custom ornamental gate that weighs several hundred pounds and needs to close perfectly every time, for years.
Why Ironworks Gate Co. Is Highland Village’s Preferred Gate Parts & Welding Company
Highland Village is not a chain-link fence town. Drive the streets around Highland Shores or the lakefront coves off Yacht Club Road and you will see ornamental iron, tubular steel, custom scrollwork. These are heavy, expensive gates, and they fail in specific ways that take experience to diagnose. We have spent over 42 years as a company learning exactly how they fail, and we bring that experience to every home in Highland Village we service.
Victor Salinas leads our team, and he has built the company around a simple promise: done right, and backed in writing. Every job we complete, including parts replacement and welding work, carries our 90-Day Done Right Promise. If it is not right, we come back and make it right. No paperwork, no arguing, no exceptions. That is the Keystone Standard we apply to every hinge, every weld, every post reset.
When you call us from Highland Village, a live person answers. Not an answering service, not a voicemail tree. That matters when your gate is stuck open and your dog is eyeing the street. We answer the phone 24 hours a day, seven days a week.
Key Takeaways
- Parts and welding repair for ornamental and custom driveway gates in Highland Village, TX.
- Specialists in hinge replacement, post replacement, rail repair, and custom welding.
- Pricing is quoted and agreed before work starts. No surprises on the bill.
- 90-Day Done Right Promise on every completed job, in writing.
- We service nine major automation brands, including LiftMaster, DoorKing, and Elite.
- $50 off any repair over $250. Free second opinion on any written estimate.
Our Gate Parts & Welding Services in Highland Village
Hinge Replacement
In Highland Village, hinges take the brunt of two forces: the weight of a heavy ornamental gate and the corrosive lake air that settles on the shoreline. We replace worn barrel hinges, cut out rust-seized pins, and weld in new powder-coated hardware that is sized for the actual weight of your gate. Not a generic hinge from a box store. A hinge selected for the panel you have, on the post you have, in the climate you live in. The work is done right, and it is backed in writing.
Post Replacement
The soil under Highland Village is expansive black clay. It swells in wet winters and shrinks in summer heat, and over time that movement tilts gate posts. A post that moves even a quarter-inch will make a swing gate drag on the latch side, or fail to close altogether. We cut out the old post, dig a deeper footing, set a new post in fresh concrete, and re-hang your gate so it swings true. When the post is squared away, your gate works the way it did when it was first hung.
Rail Repair
Bottom rails on ornamental gates take abuse. They sit close to the ground, they catch splash-back during rain, and they are often the first section to rust through. We cut out rotted sections, splice in new matching rail, and grind the weld smooth so the repair disappears into the original work. If the damage is too far gone for a splice, we will tell you straight. But in most Highland Village gates we have seen, the rail can be saved.
Custom Welding
Some gates were built for a different house, or a different era, and no off-the-shelf part will fit. We do custom welding in Highland Village regularly: fabricating new hinge brackets, extending gate panels, adding steel supports inside hollow rails, and repairing decorative scrollwork that has cracked at the weld points. Victor Salinas started in this trade with a welder in his hand, and that craft still drives the company. Custom iron work is not a side business for us. It is the foundation.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Highland Village
Most ornamental gates in Highland Village are automated, and the operator is only as good as the metal it is bolted to. Our technicians are trained and equipped on nine gate-automation brands, including LiftMaster, DoorKing, and Elite. When we replace a hinge or reset a post on an automated gate, we also check that the operator, safety photocells, and travel limits are still in spec. Because a gate that swings freely but trips the entrapment protection is not actually fixed. We stock common parts locally for Highland Village customers, so most jobs are completed in a single visit.
Common Gate Parts & Welding Problems We See in Highland Village Homes
- Rust-seized hinge pins near the lake. We recently re-hung a custom ornamental swing gate on a Highland Shores estate where the hinge post had shifted a full inch over two North Texas drought-winter cycles. Our crew cut and re-welded new powder-coated barrel hinges, reset the gate post in fresh concrete with a deeper footing, then recalibrated the LiftMaster operator and safety photocells so the heavy gate sweeps without dragging or tripping the entrapment protection. Along the shoreline, the lake breeze keeps metal damp overnight even in summer, and hinge pins can seize solid in eight to ten years.
- Posts tilted by expansive clay. The black clay under this part of Denton County shifts with every wet-dry cycle. Swing gate posts lean gradually, the latch side drops, and the gate stops closing. We reset posts with a deeper footing to resist the seasonal movement.
- Sagging ornamental panels with heavy scrollwork. Custom gates with decorative steel scrollwork put a lot of load on the hinge side. If a previous repair only addressed the panel and not the post, the gate sags again. We fix the root cause, not just the symptom.
- Corroded operator brackets. The mounting brackets that hold your gate operator corrode faster near Lake Lewisville than they do a few miles inland. Pitted brackets flex under load, throwing the operator out of alignment. We replace them with heavier-gauge steel and treat the new metal for the humidity it will face.
Pricing for Gate Parts & Welding in Highland Village, TX
Here is what you can expect for common welding and parts work in Highland Village. Hinge replacement on a standard ornamental gate typically runs $180-$340 per hinge, including the new hinge, welding, and alignment. Post replacement, including cutting out the old post, setting a new one in concrete, and re-hanging the gate, runs $450-$900 depending on post size and access. Rail repair, where we splice in matching steel, generally runs $150-$400. Custom welding work is quoted by the job after we see the gate, but small fabrication fixes start around $120.
You will know the full price before we start. That is a square deal: upfront price, no surprises on the bill. We also run a standing offer: $50 off any repair over $250, a free second opinion on any written estimate, and an $89 seasonal tune-up. Seniors and veterans always receive a 5% discount. Call (432) 547-6481 for an exact quote on your gate.
We Also Serve Cities Near Highland Village
Our gate parts and welding technicians work throughout this corner of Denton County. In addition to Highland Village, we serve Little Elm, Frisco, Aubrey, and Cross Roads. If you live just outside Highland Village and need a hinge replaced, a post reset, or a custom weld, call us and we will get you scheduled. Dispatch for all these areas is coordinated from our Dallas-Fort Worth office, with crews serving Highland Village locally.
Serving Highland Village, TX - Our Local Coverage Area
We’re based in the Highland Village area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Highland Village
The clay soil under your gate post dried out and shrank over the summer, and the post leaned just enough to drop the latch side of the gate. This is the most common seasonal gate problem we see in Highland Village. The fix is resetting the post in a deeper footing and re-hanging the gate so it clears the ground across the full swing. Call (432) 547-6481 and we will come take a look. The quote is free.
Closer to the shoreline, on lots near Yacht Club Road or the Highland Shores coves, we see hinge pins seize and operator brackets pit within eight to ten years. That is significantly faster than gates just a few miles inland in Flower Mound, because the lake breeze keeps iron damp overnight even in dry weather. Welding can repair most of it: we cut out the rotted sections, weld in new steel, and re-treat the metal so it holds up better going forward.
In most cases we can salvage the gate. We cut out the section of bottom rail that is rotted through, splice in a new matching section of steel, and grind the weld smooth. The repair disappears into the original work. If the entire frame is compromised, we will tell you straight and talk through your options, but we rarely recommend replacing a Highland Village ornamental gate that can be safely repaired.
Usually it is both. The binding is a mechanical problem: a hinge that is worn or seized, or a post that has drifted out of plumb. That is welding and parts work. But once the gate is moving freely again, the operator often needs its travel limits and force settings recalibrated so it is not fighting the old resistance. We do both in the same visit on most Highland Village jobs.
The right way is to cut out the old hinge pin and bracket entirely, weld a new barrel hinge onto the post with proper heat control, and size the new hinge for the actual weight of the gate. Drilling extra holes into a post to bolt on a surface hinge weakens the steel and will fail again. We remove the old hinge cleanly, prep the surface, weld the replacement, and treat the area against the lake humidity. Call (432) 547-6481 and we will get you on the schedule.
Call Ironworks Gate Co. for Gate Parts & Welding in Highland Village
When your gate is dragging, rusting, or refusing to latch, call us. A live person answers, day or night. We will schedule a technician to your Highland Village home, give you a straight quote before any work begins, and stand behind the completed job with our 90-Day Done Right Promise, in writing. That is how we have done business for over 42 years, and that is how we will do it for the next 42.
Call (432) 547-6481 today for a free estimate.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Highland Village and surrounding communities.